FR-J20P

+86 13786124329
Language:EN
CN
FR-J20P
Fiber Optic Sensor
FR-J20P
  • Easy to use 2 digital pictures

  • Various control functions are available to effectively reduce costs

  • Simple and clear button design

  • Stable detection of small objects, transparent body, the amount of light can be adjusted
  • Key lock function to prevent misoperation

  • Lead-out type

Product Certification

  • CE
  • ROHS
Easy to use 2 digital pictures
With two digital screens, it is possible to simultaneously confirm the reference value, the amount of light incident, and perform various settings, with extremely strong operability.
#: You can use numerical values to set the benchmark, and the indication is also very simple
#: Current value at a glance
Various control functions are available to effectively reduce costs
In the case of maintaining the function and performance of the original FR-J16 series of products, through structural optimization and the introduction of automated production, the cost of the product has been effectively reduced, effectively improving the cost performance of the product.
Simple and clear button design
The reference value adjustment and switching switch are operated by buttons, and the infrequently used functions are set through the built-in function menu.
Stable detection of small objects, transparent body, the amount of light can be adjusted
In the case of close detection, detection of transparent objects or small objects, when the light level reaches saturation, the amount of light projected by the sensor can be reduced to achieve stable detection.
Key lock function to prevent misoperation
The operator can be prevented from erroneously changing the reference value.
Outlet mode
Lead-out type (standard two-meter meander-resistant cable).
KindShape (mm)NPN TypePNP type
Outlet type1697187651177828.jpgFR-J20N FR-J20P



Light source (luminous wavelength)Red LED640nm
Power consumption/current consumption≤ 30mA
Output modeNPN open collector
Switch modeL.on (incoming light action)/D.on (shading action) can be set
Switching frequencySTD:2KHZ;LONG:25Hz;HS:10KHz
Indicator lightOrange output status indication (integrated on the display)
Display8-bit 7-segment digital tube (left four yellow-green, right four red)
Light modulation modeMulti-level luminous power and receive signal gain adjustment function
Response timeSTD:250US;LONG:20ms;HS:50uS
Timer functionON delay, OFF delay, ONE SHOT timer
Practical functionParameter initialization/key lock/threshold two-point, fully automatic and manual setting
Advanced FeaturesBasic value tracking, adjustable luminous frequency to prevent mutual interference, offset setting, area detection
Delay functionNo timing, OFF delay, ON delay, SHOT delay
Power supply voltageDC12 ~ 24V ± 10% pulsation (P-P) below 10%
Load currentBelow 100mA
Insulation resistanceAbove 20MQ (DC500 megohmmeter) between charging part and shell
Ambient temperature-10°C ~ 50°C (no freezing)
Ambient humidity35~85%RH
ambient illuminationIncandescent lamp ≤ 20000LX; Sunlight ≤ 30000LX
protection circuitSurge protection, short circuit protection (continuous short circuit about 800us to determine short circuit) polarity reverse protection
Impact resistance500 m/s, 2 hours in X,Y and Z directions
shock resistance10~55Hz, amplitude 1.5mm, 2 hours in X,Y and Z directions
Connection modePair cord type M8 three-core connector
MaterialPC


FR-J20P
DC 3-wire PNP output
Selection Manual
  • Selection Manual
    Selection Manual
    FR-J20 Series Digital Fiber Amplifier
Instructions
  • Instructions
    Instructions
    FR-J20 series digital optical fiber sensor product manual

    PDF: Simplified/230915

CAD
  • CAD
    CAD
    FR-J20 Series Digital Fiber Optic Sensor Products 3D Digital Analog
Certification Certificate
  • Certification Certificate
    Certification Certificate
    FR-J_ROHS_SGS
  • Certification Certificate
    Certification Certificate
    FR-J20_CE_SGS
  • Certification Certificate
    Certification Certificate
    FR-J20_CE
Focus on us